Olympia Chimney Chimney Repair in Orlando: What to Know First
As an independent Olympia Chimney service provider, we repair Olympia Chimney flue systems, liners, and components across Orlando - most jobs completed in a single visit with upfront pricing. A typical Olympia Chimney repair in Orlando runs $280 to $1,850 depending on whether we’re sealing a liner joint or rebuilding a chase, and we carry the common parts so we’re not ordering and hoping. We do not mark up parts to pad the bill, and we do not start work until you know the full number.
This page is for homeowners in Orlando, Winter Park, College Park, and Baldwin Park who have an Olympia Chimney product - likely a stainless steel liner, a factory-built chimney, or a pellet venting system - and need straight talk about what’s wrong and what it costs to fix it. Call (877) 565-7563 and a live person will answer, 24 hours a day.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia 316Ti flexible liner collars separate at the seam in Orlando’s humidity. The 316Ti series uses a titanium-stabilized alloy that resists acid corrosion, but the draw-band collar connection was redesigned in 2019 and earlier units rely on a single mechanical joint. We see this in Baldwin Park homes with gas inserts where the collar works loose from thermal cycling. Our fix: remove the damaged section, install a new Olympia-spec collar with a second locking band, and pressure-test the joint before we leave.
- Olympia pellet venting (OPV series) accumulates fly ash at the tee cleanout that hardens to concrete in Florida’s moisture. The OPV 3-inch and 4-inch tees have a shallow cleanout cup that fills faster than the owner realizes. By the time there’s a draft problem, the tee is packed solid. We pull the tee, inspect the liner walls with a camera, and replace with an Olympia tee or a HeatShield-compatible unit if the original is discontinued. A clean chimney is not a luxury - it is just the job done right.
- Olympia chimney chase covers in the 3000 series pool water at the corners after ten to fifteen Orlando summers. The galvanized steel covers with factory crimped edges hold water where the paint first fails - usually the northeast corner from morning sun exposure. We fabricate a replacement from heavier-gauge Gelco or Copperfield stock, extend the drip edge past the chase wall, and seal with a high-temp silicone that flexes through our freeze-thin freeze cycles.
- Olympia air-cooled chimney systems lose draft in tightly sealed Florida homes. The air-cooled design pulls combustion air from around the chimney, but modern HVAC and spray-foam insulation create negative pressure that starves the fire. We see this in Winter Park renovations where the original 1980s chimney was retained. Our fix: convert to a sealed-combustion direct-vent using DuraFlex components, or install a code-compliant outside air kit - whichever the home’s layout allows.
- Olympia chimney crown mortar cracks within eight years on south-facing exposures in Orlando. The factory crown is a precast concrete cap with a thin mortar bed that cures hard and brittle. Our afternoon thunderstorms drive water into hairline cracks; the next day’s sun steams it back out. We grind back to sound concrete, apply a bonding agent, and repoint with a modified mortar that retains flex. For crowns too far gone, we pour a new cast-in-place crown with proper overhang and drip groove.
Our Olympia Chimney Chimney Repair Process
- 1
Call and describe what you’re seeing. A live person answers, notes your Olympia Chimney model if you know it, and schedules a visit - usually within 24 to 48 hours in Orlando.
- 2
Level-2 camera inspection with photos you can see. Our technician runs a chimney camera and shows you the footage on a tablet. You get a plain-English verdict: what failed, why it failed, and what happens if you wait.
- 3
Parts decision: Olympia OEM or quality equivalent. If your part is in current production, we quote Olympia OEM. If it’s discontinued - some OPV fittings and early 316Ti collars - we source from Famco or Gelco with matching specs, and we tell you before we order.
- 4
Repair with no-hassle upfront pricing. The number on the estimate is the number on the invoice. We complete most Olympia Chimney repairs in a single visit because we stock the common failures.
- 5
Test, document, and guarantee. We pressure-test liner joints, verify draft with a manometer, and photograph the finished work. Your receipt includes the 90-Day Done Right Promise in writing - if it’s not right, we come back, no arguing.
- 6
Cleanup and next-service reminder. We leave the work area cleaner than we found it and note your next recommended inspection date - typically twelve months for gas, six for wood-burning in Orlando’s climate.
What Olympia Chimney Chimney Repair Costs in Orlando
These are real ranges from jobs we’ve completed in Orlando, Winter Park, and College Park. Your exact quote comes after inspection - estimates are free.
| Repair | Typical Range | What Moves the Price |
|---|---|---|
| Olympia liner collar reseal / band replacement | $280 - $450 | Height of chimney, number of joints, access |
| OPV pellet tee cleanout and replacement | $340 - $620 | Degree of ash compaction, liner wall condition |
| Chase cover replacement (Gelco/Copperfield) | $580 - $1,100 | Chase dimensions, custom fabrication, height |
| Air-cooled to direct-vent conversion | $890 - $1,850 | Routing new venting, wall penetration, finish work |
| Crown repoint or rebuild | $420 - $980 | Crown size, crack depth, scaffold needs |
Factors that raise or lower your price: chimney height above roofline, whether we need scaffolding versus roof access, and whether the Olympia part is current stock or special order. We do not charge extra for after-hours or weekend calls - the rate is the rate.
Call (877) 565-7563 for your exact quote. Estimates are free, and we honor our standing offers: $50 off any repair over $250, free second opinion on any written estimate, $89 seasonal tune-up, and a permanent 5% senior and veteran discount.
Why Orlando Homeowners Call Hearthstone Chimney Co. of Orlando for Olympia Chimney Work
We’ve been answering the phone with a live person for over 42 years, and we plan to be here in thirty more. That changes how you treat a customer - you don’t gamble with a reputation you’re still building.
Our technicians are background-checked, uniformed, and trained on Olympia Chimney’s product line specifically, not just generic chimney work. When an Olympia part is discontinued, we know which Famco or Gelco equivalent meets the thermal and corrosion specs because we’ve installed them in Orlando homes that get inspected annually.
The 90-Day Done Right Promise governs every job: Krafted right, Every time, Your home first, Standing behind it. In writing. No arguing. If it’s not right, we make it right.
Roy Dempsey grew up in College Park working on his grandfather’s bungalow fireplace, and he’s spent the better part of four decades on Orlando roofs. He’ll tell you when a chimney needs real work and when it just needs a good cleaning - and he does not confuse the two.
FAQs
No, independent repair does not automatically void your warranty, but using non-OEM parts on a still-covered component can. We check your purchase date and warranty status before quoting, and if you’re within the warranty window, we’ll tell you to call Olympia Chimney first - that’s the square deal. Call (877) 565-7563 and we’ll walk through it with you.
We stock the common failure parts - 316Ti collars, OPV tees, standard chase covers - so most repairs happen same-day. Special-order Olympia parts take three to five business days, and we’ll tell you before we schedule if that’s the case. Call (877) 565-7563 to check availability for your model.
Repair is usually the better value if the liner or chase is structurally sound and the failure is localized - a collar, a tee, a crown. Replacement makes sense when the system is past 20 years, multiple components are failing, or the original installation was substandard. We give you both numbers and our honest recommendation. Call (877) 565-7563 for a free inspection and straight answer.
If you have water pouring through the chase, a detached liner, or a blocked flue with a fire in use, we treat it as urgent and dispatch same day when possible. Our phones are staffed live 24/7 - not a voicemail, not a callback queue. Call (877) 565-7563 and we’ll tell you our first available slot.
Yes. We service and repair systems using DuraFlex, HeatShield, Gelco, Famco, and Copperfield components daily. Many Orlando homes have mixed-brand systems from repairs over the decades, and we carry the cross-reference knowledge to match parts correctly. Call (877) 565-7563 with your setup and we’ll confirm we can handle it.
Ready to get your Olympia Chimney fixed right? Call Hearthstone Chimney Co. of Orlando at (877) 565-7563. A live person answers 24 hours a day, and we’ll schedule your free estimate at a time that works - no pressure, no surprises, just the job done right and backed in writing.
Written by Roy Dempsey, Owner & Master Sweep, Hearthstone Chimney Co. of Orlando at Hearthstone Chimney Co. of Orlando, serving Orlando and nearby areas.